
Most roofs in the U.S. rest on one of two panel types: plywood or OSB (oriented strand board). Both are structural panels, and both meet the same span ratings when they carry the right stamp. Fine Homebuilding describes solid sheathing, which is almost always plywood, OSB or another structural panel, as the standard choice. Open sheathing, which is spaced boards, is the exception under wood shingles and shakes. For a house or small commercial building on the Gulf Coast, the real question is rarely which panel type wins. It is whether the panels under your shingles are the right thickness, properly rated and still sound. We look at that on every inspection, and this guide shows you what to look for.
TL;DR
- Roof sheathing (also called roof decking) is the layer of panels nailed to the rafters or trusses. Shingles, metal or tile are installed on top of it.
- The two basic types are solid sheathing (plywood or OSB) and open sheathing (spaced boards, used under wood shingles and shakes).
- OSB usually costs 20% to 30% less per sheet. Plywood dries faster and swells less at the edges. Both meet the same APA span ratings.
- Check three things on any panel: the APA stamp, the span rating and the exposure rating. They matter more than the brand or the material.
- Damaged sheathing is replaced with panels of the same thickness. If more than about 10% of a roof needs repair, a new roof is the usual recommendation.
Table of Contents
- Sheathing, decking and the roof deck: the same layer
- The main roof sheathing types
- OSB vs. plywood roof sheathing side by side
- Thickness, span rating and exposure rating
- What roof sheathing costs when it gets replaced
- When sheathing needs repair or replacement
- Sheathing and your roofing material
- Sheathing after a storm
- How we help with roof sheathing in Baytown
- Our view on sheathing
- FAQ
- Sources
Sheathing, decking and the roof deck: the same layer
Contractors use “sheathing,” “decking” and “roof deck” almost interchangeably. Some professionals reserve “sheathing” for panels and “decking” for boards or any structural surface, but on a typical home they mean the same layer. It sits between the framing and the underlayment (the water-resistant sheet under the roof covering). It does three jobs:
- It gives the roof covering a flat, solid surface to be fastened to.
- It ties the rafters or trusses together so the roof acts as one structural plane. Fine Homebuilding notes that solid sheathing acts as a diaphragm, which means it carries sideways loads such as wind through the building.
- It holds fasteners. Shingle nails and sheathing nails only work if the panel underneath is sound.
Because you never see it once the roof is finished, sheathing is the part of a roof most homeowners know least about. It is also the part that turns a routine re-roof into a bigger job when it has been wet for a long time.
The main roof sheathing types
Plywood
Plywood is made of thin wood veneers glued in layers, with each layer’s grain running across the one below. That cross-layering is why plywood swells evenly and dries relatively quickly after it gets wet. On roofs, the common grade is CDX, which is the sheathing grade with a rougher face that suits a surface that will be covered. The WSRCA technical bulletin says plywood’s cross-layered veneers allow even swelling and faster drying.
OSB (oriented strand board)
OSB is made from thin wood strands, laid in cross-oriented layers, then bonded with adhesive and wax under heat and pressure. According to the same bulletin, it is manufactured mostly from southern yellow pine, aspen and poplar. Its exposed strand ends absorb moisture more readily than plywood faces. That matters if a roof sits open to rain during a long job or leaks for months. Its advantages are cost and consistency: The Roofing Brief reports more uniform thickness and grade from panel to panel, with the same APA span ratings as plywood.
Other structural panels
Some panels are made from other engineered wood products, and the guidance treats them like plywood and OSB as long as they are performance-rated structural panels. The JLC field guide says sheathing should consist of performance-rated structural panels carrying the stamp of APA, The Engineered Wood Association.
Open (skip) sheathing and plank boards
Open sheathing is made from boards spaced apart. It is used under wood shingles and shakes, which need ventilation on both sides, according to Fine Homebuilding. Older homes, especially pre-war ones, may also have solid lumber planks. Asphalt shingles, metal panels and most other coverings need a solid surface, so a roof with spaced boards usually gets covered with panels before a new roof goes on.
OSB vs. plywood roof sheathing side by side
| Factor | Plywood (CDX) | OSB |
|---|---|---|
| Construction | Cross-layered wood veneers | Compressed, cross-oriented wood strands |
| Typical 2025 price per 4x8 sheet | $36 to $52 (15/32-inch) | $22 to $32 (7/16-inch) |
| Moisture behavior | Swells evenly, dries faster | Exposed strand ends absorb water more readily |
| Maximum moisture content at installation | 18% | 16% |
| Span ratings | Same APA ratings as OSB | Same APA ratings as plywood |
| Panel consistency | Varies more from sheet to sheet | More uniform thickness and grade |
The prices come from The Roofing Brief, which puts OSB at 20% to 30% cheaper per sheet. The moisture limits come from the WSRCA bulletin, which also says both materials are made from sapwood considered moderately decay resistant.
Prices for lumber products move with the market and vary by supplier. Treat the figures above as a 2025 range for comparing the two panels, not a quote. The price gap between the two can change too: an index tracked by Buildermuse shows softwood veneer and plywood rising faster than OSB-type products over the year to September 2026.
So which is best for roofs?
There is no single winner. Either panel is acceptable if it carries the correct APA stamp, the right span rating and the right exposure rating for how your roof will be built. In wet climates like the Houston area, a plywood deck has a modest edge in forgiving a wet spell. OSB gives you a lower material cost and a flat, even surface. For a roof that will be covered quickly, both perform well. For a roof that may sit open to weather, such as after storm damage, the exposure rating matters more than the panel type.

Thickness, span rating and exposure rating
Three markings on the panel tell you whether it is the right one.
Thickness. Under the 2024 IRC, the minimum sheathing thickness for a 24-inch rafter span is 15/32-inch plywood or 7/16-inch OSB, according to The Roofing Brief. Local codes adopt the IRC with their own amendments, so the exact requirement in your city comes from the local building department. Where an older deck must be replaced, the City of Bedford, Texas states that rotted, dilapidated or structurally substandard decking must be replaced to meet current code before new underlayment and roof covering go on.
Span rating. The span rating is a pair of numbers stamped on the panel, such as 24/16. It tells you the maximum spacing of supports for that panel. InterNACHI explains that maximum span is limited by stresses and deflections caused by design loads, and that inspection agencies label panels with those spans. A cheaper panel with a lower span rating is not an equivalent substitute, which is why quotes should compare panels of the same rating.
Exposure rating. APA classifies panels by how well the glue resists moisture. According to the WSRCA bulletin, Exposure 1 panels resist short-term wetting from construction delays, while Exterior panels have bonds that withstand repeated wetting and drying or long-term weather exposure. The FEMA hurricane guide says panels rated Exposure 1 or better should be used on roofs. At exposed eaves and rakes, Fine Homebuilding notes that a more expensive weather-rated grade is required.
In high-wind areas, FEMA says panels typically need to be 15/32-inch or thicker, and that plywood provides higher nail-head pull-through resistance than OSB. For homes on the upper Texas coast, that is a useful detail to keep in mind when a roof is being replaced.

What roof sheathing costs when it gets replaced
A roof only needs new sheathing when the old panels are damaged. When that happens, the cost is added to the roofing job. The Roofing Brief reports that full re-decking on a 2,400-square-foot house adds $2,000 to $6,000 to a re-roof. That figure assumes roughly 30 to 40 sheets at $65 to $150 installed per sheet. Partial repairs cost much less, because only the damaged sheets are replaced.
A few things drive the number:
- How much of the deck is damaged. One wet corner is a different job than a deck soaked throughout.
- Panel type and thickness. Plywood costs more per sheet than OSB, and thicker panels cost more than thinner ones.
- Access and roof pitch. Steeper, more complex roofs take more labor per sheet.
Because sheathing damage is hidden until the old roof comes off, a fair estimate states a unit price per sheet for replacement. That way, the final bill follows what is actually found on the deck.
When sheathing needs repair or replacement
Sheathing fails for predictable reasons: a long-running leak, condensation from poor attic ventilation, storm damage, or panels left exposed during a delayed re-roof. These are the signs a deck may be compromised:
- Soft, spongy or bouncy spots when someone walks across the roof.
- Sagging between rafters or trusses.
- Dark stains, mold or damp insulation on the attic side of the deck.
- Visible daylight through the deck.
- Shingles that look wavy or have nails backing out.
The Florida Hurricane Retrofit Guide advises inspecting the roof deck for sections that are rotted, delaminated, warped or structurally unsound, and replacing them with similar material of the same thickness. It also says to check how the deck is nailed to the rafters or trusses.
What a correct sheathing repair looks like
Government guidance is specific about the details, and it is worth knowing them when you read a proposal:
- Same thickness. The Department of Energy roof repair guide recommends replacing localized damage with panels of the same thickness, so the roof surface stays flat.
- Ring-shank nails. The same guide recommends 8d ring-shank nails at 6 inches on center for new and existing sheathing. For a full replacement, it suggests considering 32/16-rated panels at least 5/8 inch thick, with nails at 4 inches on center next to a gable end.
- Nail size and head. The FEMA guide says an 8d nail, 2.5 inches long, is the minimum size for fastening panels, and full round heads are recommended to avoid pull-through.
- Staples. The Florida guide says engineering tests and hurricane experience show staples do not hold roof sheathing down well.
- Edge gap. FEMA recommends a 1/8-inch gap between panel edges for expansion, and notes that panels cut slightly short of 48 by 96 inches carry a “Sized for Spacing” label.
- No overdriving. The DOE guide warns that overdriven nails can significantly reduce the uplift strength of the connection.
Repair or replace the whole roof?
The DOE guide cites the Journal of Light Construction field guide: if more than 10% of the old roof needs repair, a new roof is recommended. That is a useful rule of thumb when you are weighing a patch against a full replacement. It also explains why sheathing condition belongs in every roof assessment. If you are also deciding between covering over an old roof and removing it, our guide to roof overlay versus tear-off shows what each approach means for the deck underneath.
Sheathing and your roofing material
The covering you choose affects how much the deck matters. Asphalt shingles, metal and tile all need a solid, flat, well-fastened deck. Tile adds substantial weight, so the framing and deck must be sound before it goes on. If you are choosing between materials, our comparison of asphalt shingles and metal roofing covers the tradeoffs for Texas homes. Low-slope commercial roofs follow different rules, and our overview of commercial roof types explains the main membrane systems and what each needs underneath.
Sheathing after a storm
Storm damage is where sheathing questions come up most. Wind can lift shingles and expose the deck. Wind-driven rain can then soak panels, and repeated wetting is exactly what the WSRCA bulletin says calls for Exterior-bond panels and a temporary weather covering. A roof that has been tarped promptly usually has a better outcome than one left open.
For insurance, the condition of the deck is part of what gets documented. Photos of any soft or stained panels, along with the date and cause of loss, help show the scope of the repair. Our storm damage roof repair page explains how that process works in Baytown.
How we help with roof sheathing in Baytown
Sure Claim Roofing is a locally owned roofing company serving Baytown and surrounding communities, for homes and commercial buildings. We offer free, no-obligation roof inspections with photo documentation and a plain explanation of your options. We recommend repair when repair is enough, and we help with insurance claim documentation when storm damage is involved. If your roof is leaking right now, our emergency roof repair team is available seven days a week.

If you already know you need a new roof, see our roof replacement services.
Our view on sheathing
Homeowners often ask us whether OSB or plywood is better. We understand why: it is the one visible choice on the material list. But the panel type is usually not what decides how a roof performs. The condition of the deck, how it is fastened and how long it sat exposed during the job usually matter more.
That is why we start with an honest look at what is already there. A free inspection with photos lets you see the same things we see, and it lets you decide with facts instead of pressure. If a repair will do, we say so. If the deck is damaged enough that replacement is the better value, we explain why and show you.
For storm damage, we believe documentation is part of the work. Clear photos and a written scope make an insurance claim easier to follow for everyone involved, and we help with that so you do not have to figure it out alone.
FAQ
What should roof sheathing be made of?
On most homes it should be a performance-rated structural panel, either plywood or OSB, carrying the APA stamp. The JLC field guide gives that as the standard. Spaced boards are used only under wood shingles and shakes.
Is OSB or plywood better for a roof?
Both meet the same span ratings. OSB costs less per sheet and is more uniform, while plywood dries faster and swells less at the edges. The right choice depends on the budget, the exposure rating and how long the deck may sit open to weather.
What thickness should roof sheathing be?
Under the 2024 IRC, a 24-inch rafter spacing calls for 15/32-inch plywood or 7/16-inch OSB, per The Roofing Brief. Your city may adopt amendments, and high-wind areas often call for 15/32-inch or thicker panels. A roofer can confirm what your local building department requires for your address.
Does a new roof always need new sheathing?
No. Sound panels can stay. Only rotted, delaminated or structurally weak sections are replaced, using panels of the same thickness. When more than about 10% of the old roof needs repair, a full replacement is usually recommended.
How do I know if my sheathing is damaged?
Look for soft spots underfoot, sagging, attic stains or mold, and visible daylight. A free inspection with photos can confirm what is happening before you decide on a repair.
Sources
- JLC Field Guide: Sheathing and Shear Panel
- Roof Sheathing, Fine Homebuilding
- WSRCA Technical Bulletin: Wood Decks Susceptibility to Moisture
- Roof Sheathing: OSB vs Plywood, The Roofing Brief
- Roof Deck Repair Cost, The Roofing Brief
- OSB vs Plywood Prices 2026, Buildermuse
- Inspecting Roof Panel Sheathing, InterNACHI
- Roof Sheathing, FEMA Hurricane Guide
- Hurricane Retrofit Guide: What To Do When Re-Roofing
- Repairing Roofs and Ceilings, U.S. Department of Energy